Linux version 2.6.10-rc3 (jim@hypnosis) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #6 Sat Dec 11 11:33:57 EST 2004
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
 BIOS-e820: 00000000000dc000 - 00000000000e0000 (reserved)
 BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000002f6f0000 (usable)
 BIOS-e820: 000000002f6f0000 - 000000002f6fc000 (ACPI data)
 BIOS-e820: 000000002f6fc000 - 000000002f700000 (ACPI NVS)
 BIOS-e820: 000000002f700000 - 000000002f780000 (usable)
 BIOS-e820: 000000002f780000 - 0000000030000000 (reserved)
 BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
 BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
759MB LOWMEM available.
On node 0 totalpages: 194432
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 190336 pages, LIFO batch:16
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f6fe0
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000001) @ 0x2f6f6958
ACPI: FADT (v002 MATBIO CF-M34-5 0x06040000 MAT  0x00000001) @ 0x2f6fbf54
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x2f6fbfd8
ACPI: DSDT (v001 MATBIO   CF-M34 0x06040000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro 
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (015f8000)
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 863.954 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 767248k/777728k available (1824k kernel code, 9856k reserved, 744k data, 148k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 1712.12 BogoMIPS (lpj=856064)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
CPU: After vendor identify, caps:  0383f9ff 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 512K
CPU: After all inits, caps:        0383f9ff 00000000 00000000 00000040
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Mobile Intel(R) Pentium(R) III CPU - M   866MHz stepping 04
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
    ACPI-0294: *** Info: Table [DSDT] replaced by host OS
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9b2, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041105
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-1 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 28)
ACPI: PCI Interrupt Link [LNKA] (IRQs *9)
ACPI: PCI Interrupt Link [LNKB] (IRQs *9)
ACPI: PCI Interrupt Link [LNKC] (IRQs 5) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs *9)
ACPI: PCI Interrupt Link [LNKE] (IRQs *9)
ACPI: PCI Interrupt Link [LNKF] (IRQs *9)
ACPI: PCI Interrupt Link [LNKG] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to bjorn.helgaas@hp.com
** so I can fix the driver.
Simple Boot Flag at 0x38 set to 0x1
Machine check exception polling timer started.
Initializing Cryptographic API
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BATA] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Video Device [GRFX] (multi-head: yes  rom: no  post: no)
ACPI: Processor [CPU0] (supports C1 C2 C3)
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [TZC] (55 C)
Real Time Clock Driver v1.12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 9 (level, low) -> IRQ 9
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH3M: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5
ICH3M: chipset revision 2
ICH3M: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1840-0x1847, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: HITACHI_DK23EA-30, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ide1: Wait for ready failed before probe !
ide2: I/O resource 0x3EE-0x3EE not free.
ide2: ports already in use, skipping probe
Probing IDE interface ide3...
ide3: Wait for ready failed before probe !
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hda: max request size: 128KiB
hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
input: PC Speaker
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
ACPI wakeup devices: 
MPCA MPCB CDB0 SMDM PWRB  LID 
ACPI: (supports S0 S3 S4 S5)
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
Adding 982288k swap on /dev/hda2.  Priority:-1 extents:1
input: PS/2 Generic Mouse on isa0060/serio4
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel 830M Chipset.
agpgart: Maximum main memory to use for agp memory: 682M
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1d.0: Intel Corp. 82801CA/CAM USB (Hub #1)
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 9, io base 0x1800
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 9
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 9 (level, low) -> IRQ 9
uhci_hcd 0000:00:1d.1: Intel Corp. 82801CA/CAM USB (Hub #2)
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 9, io base 0x1820
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
hw_random: RNG not detected
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 49407 usecs
intel8x0: clocking to 48000
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1f.6 to 64
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
ACPI: PCI interrupt 0000:01:01.0[A] -> GSI 9 (level, low) -> IRQ 9
eth0: RealTek RTL8139 at 0xf0138000, 00:d0:59:46:18:a5, IRQ 9
eth0:  Identified 8139 chip type 'RTL-8139C'
airo:  Probing for PCI adapters
ACPI: PCI interrupt 0000:01:04.0[A] -> GSI 9 (level, low) -> IRQ 9
airo: Found an MPI350 card
airo: MAC enabled eth1 0:2:8a:dd:d6:5e
airo:  Finished probing for PCI adapters
Linux Kernel Card Services
  options:  [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 9
ACPI: PCI interrupt 0000:01:05.0[A] -> GSI 9 (level, low) -> IRQ 9
Yenta: CardBus bridge found at 0000:01:05.0 [10f7:8338]
Yenta: ISA IRQ mask 0x0c98, PCI irq 9
Socket status: 30000006
cs: IO port probe 0x0100-0x04ff: excluding 0x360-0x367 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0354de0(lo)
IPv6 over IPv4 tunneling driver
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 9 (level, low) -> IRQ 9
[drm] Initialized i830 1.3.2 20021108 on minor 0: Intel Corp. 82830 CGC [Chipset Graphics Controller]
[drm] Initialized i830 1.3.2 20021108 on minor 1: Intel Corp. 82830 CGC [Chipset Graphics Controller] (#2)
mtrr: base(0xe8000000) is not aligned on a size(0x258000) boundary
eth1: no IPv6 routers present